Guličkové skrutky sú najčastejšie používané prevodové komponenty v obrábacích a presných strojoch. Jeho hlavnou funkciou je premena rotačného pohybu na lineárny pohyb alebo premena krútiaceho momentu na axiálnu opakujúcu sa silu. Zároveň má tiež vlastnosti vysokej presnosti, reverzibility a vysokej účinnosti.
Excentricita: Vzťahuje sa na stredovú odchýlku medzi pevnou stranou a nosnou stranou.
Inclination: In addition to eccentricity, the installation error caused by the parallel error (up, down, left, and right) or vertical error of the screw nut mounting part between the screw shaft and the guide (LM guide, etc.).
Installation accuracy reference: Refer to the table for the reference value of the installation accuracy of the ball screw. The data in the table is for reference only. Please minimize installation errors. The installation accuracy of the motor support and coupling affects the walking and positioning accuracy of the workbench, so attention should be paid to the ball screw.
Unpacking: Be careful not to hit the nut and end thread. When disassembling the nut, you can manually rotate the nut from one end of the effective thread to the other end. Check whether the resistance is consistent and whether there is obvious bending. Be careful not to disengage the nut screw from the effective thread. Wipe off the surface anti-rust oil and apply lubricating oil.
Maintenance: When the linear speed is less than or equal to 30m/min, grease can be used for lubrication. According to the working conditions, grease should be injected every 300 to 600 working hours. It is recommended that oil lubrication be 30-60 m/min a nútené mazanie olejovou hmlou možno považovať za 60-100 m/min. Odporúča sa objednať dutú skrutku a použiť nútené chladenie a mazanie. Udržujte pracovné prostredie čisté a nedovoľte, aby sa do obežnej drážky alebo matice dostal prach a iné nečistoty. Ak situácia nie je dobrá, zvážte pridanie ochranného krytu na skrutky.
Ball screws are usually used where precise positioning is required. The ball screw has high mechanical efficiency, low transmission torque and almost zero axial clearance, making it an important device in tool positioning and aileron drive applications. However, the resistance and heat generated by continuous operation may cause large friction and positioning errors. Increasing the design coefficient of the ball screw friction will also increase the torque, which in turn affects the positioning accuracy. When the ball is pressed between the ball screw nut and the screw shaft, the wedge effect is a potential source of friction. When rotating in the forward direction, the ball is usually pressed on the nut; on the contrary, the ball is squeezed on the screw shaft. Since the sliding friction coefficient is much larger than the rolling friction coefficient ({{0}}.1-0.3 when there is no movement, 0.001-0.003 when rolling), the wedge effect greatly increases the torque.
Ball screw drive has the following advantages:
①Vysoká účinnosť prenosu. Účinnosť prenosu guľôčkovej skrutky je vo všeobecnosti 20,92-10 percent a účinnosť prenosu obyčajného posuvného skrutkového prevodu je 20,20-0.40.
②Vysoká presnosť prenosu, stabilný pohyb a žiadny jav plazenia. Pohon guľôčkovou skrutkou je v podstate valivé trenie, s malým odporom trenia a odpor trenia nemá takmer nič spoločné s rýchlosťou pohybu.
③Jazda na spiatočku bez voľnobehu. Po predbežnom utiahnutí guľôčkovej skrutky a matice- možno axiálnu vôľu odstrániť. Týmto spôsobom nevzniká mŕtva zóna v opačnom smere a zlepšuje sa presnosť a tuhosť axiálneho prevodu.
④Je to reverzibilné. Pretože strata trením guľôčkovej skrutky je malá, môže byť prevedená z rotačného pohybu na lineárny pohyb a môže byť tiež prevedená z lineárneho pohybu na rotačný pohyb. Vodiacu skrutku aj maticu možno použiť ako pohon alebo unášač.
⑤Dlhá životnosť. Vzhľadom na malú stratu valivého trenia trením je životnosť dlhá.
As a precise and labor-saving transmission mechanism, the ball screw is widely used in precision machine tools and CNC machine tools due to the above advantages.
Why not give us a linear challenge?
Kontaktuj teraz
E-mail: sales@gyballscrew.com Tel(WhatsApp): plus 86 17769816967
seller@gyballscrew.com plus 86 17769815516
saleChen@gyballscrew.com plus 86 15325179771
